Zero Halliburton Customer Care logo
Zero Halliburton Customer Care logo

All articles

Collectors Series Two-Step Lock InstructionsUpdated 2 years ago

Zero Halliburton Collectors Series travel cases are equipped with two levels of security that can work independently or in tandem. In addition to a TSA combination lock, the travel cases are equipped with biometric fingerprint technology as an additional security feature. Travelers can use the combination lock by itself or add the fingerprint scan for enhanced protection.

Operating instructions follow.

COMBINATION LOCK INSTRUCTIONS

You may open and lock the travel case with just the combination lock.

SETTING THE COMBINATION LOCK

  1. The combination lock comes with a factory preset of 0-0-0-0. Before resetting, ensure that the combination shows 0-0-0-0. (Figure 1 below)
  2. Turn the TSA007 knob counterclockwise to the unlock position. Press the reset button using a pen tip or other small pointed instrument (Figure 1). Keep the pointed instrument in the reset button until you have changed the combination dials.
  3. Set your combination by turning the dials to your desired numbers. Remove the pointed instrument to release the reset button.
  4. Turn the TSA007 knob clockwise 90 degrees to the lock position.

WRITE DOWN AND SAVE YOUR COMBINATION!

Please keep it in a secure place for future reference. Zero Halliburton cannot assist you in opening the case if you forget the combination.

UNLOCKING THE CASE

  1. Turn the dials from the lock position to 0-0-0-0 (the preset combination) or your personal combination.
  2. Turn the TSA007 knob counterclockwise 90 degrees to the unlock position (Figure 1).
  3. Press the buttons on the side sliders and move the sliders outward to open the case (Figure 1).

Figure 1

LOCKING THE CASE

  1. Close the case.
  2. Move the side sliders to the lock position (Figure 1).
  3. Turn the TSA007 knob clockwise 90 degrees to the initial lock position (Figure 1).
  4. Turn or spin the combination dials.

RECAP

When locking the case, remember to spin the combination dials to ensure that the case is completely locked.

The side sliders must also be in the lock position to ensure that the case is securely locked.

FINGERPRINT LOCK INSTRUCTIONS

The fingerprint feature can be used in conjunction with the combination lock as an added level of security. Once fingerprints are registered, the case can be unlocked by either the fingerprint sensor or the combination lock.

REGISTERING FINGERPRINTS

  1. Open the travel case and locate the battery cover on the back of the center lock bar. Remove the cover and insert 2 AA batteries (not included) in the positive (+) and negative (-) positions as indicated. (Figure 2)
    NOTE: Batteries are required for the biometric fingerprint feature to operate. To conserve battery life, flip the power switch to “OFF” when the case is unlocked and NOT in use. A low battery warning is indicated when the power switch is turned on, and the red indicator light flashes three times.
  2. Flip the power switch to “ON,” and press and hold the “SET” button for 1 second. (Figure 2)
    NOTE: Be careful not to hold the “SET” button for longer than 1 second, or you could delete all the fingerprints currently registered.
  3. You will hear two short beeps, and the indicator light will flash purple when the registration function is activated. (Figure 2)
  4. Choose a fingerprint to register and prepare to scan it three times in succession: While the purple light is flashing, place your finger on the fingerprint sensor and hold it in place for 1 second. (Figure 3)
    • If the scan is successful, you will hear one short beep, and the indicator light will turn blue. The light will then flash purple, indicating that you should place the same finger on the sensor again.
    • Repeat the process and wait for the beep and the blue indicator light, and then scan the same finger one more time, for a total of 3 scans. Once your fingerprint is registered successfully, you will hear one long beep, and the indicator light will turn blue again.
    • If either of the first two scans fails, you will hear two short beeps, and the indicator light will turn red for 2 seconds. The light will flash purple, prompting you to rescan the same finger. If the subsequent scan(s) are successfully registered, you will hear one long beep, and the light will turn blue again.
  5. Repeat the scanning process above for each additional fingerprint you want to register.

Figure 2

NOTES

The registration function will be canceled if registration activity is not detected within 10 seconds after the “SET” button is pressed.

The maximum number of stored fingerprints is 50. After that, you must delete all the fingerprints before scanning and registering new ones. The system does not allow you to delete specific fingerprints.

DELETING FINGERPRINTS

To delete your registered fingerprints, press and hold the “SET” button for 3 seconds. You will hear one long beep, and the indicator light will turn blue. All registered fingerprints will be deleted.

LOCKING THE CASE

  1. Ensure that the power switch is “ON” before locking the case.
  2. Turn the TSA007 knob to the lock position.
  3. The fingerprint lock will automatically engage when you close the case.
  4. Return the side sliders to the lock position.

UNLOCKING THE CASE

  1. Move the two side sliders on the case to the unlock position. (Figure 1)
  2. Place one of your registered fingers on the fingerprint sensor and hold it in place for at least 1 second.
    • If the fingerprint match is successful, you will hear one long beep, and the indicator light will turn blue for 10 seconds. You must open the case within 10 seconds of the fingerprint scan, or the lock will re-engage.
    • If the fingerprint match fails, you will hear two short beeps, and the indicator light will turn red. Wait for the indicator light to flash blue, then rescan your fingerprint to unlock the case.

RECAP

The travel case can only be opened when the fingerprint lock and side sliders are both in the unlock position. For safety reasons, you must open the case within 10 seconds of the fingerprint scan, or the lock will re-engage. You will need to scan your fingerprint again to unlock the case.

TSA


Was this article helpful?
Yes
No